Salter-brecknell 7815 / 7815R Manuale Utente

User’s ManualModel 7815Parcel Bench Scale

Model 7815 Parcel Bench Scale User’s Manual10Figure 2Menu Structure

Model 7815 Parcel Bench Scale User’s Manual11Input/Output (I-O) – To test the data I/O port,install a loopback connector and press the testbutton. The

Model 7815 Parcel Bench Scale User’s Manual12Configuration ModeStep-by-Step Instructionsfor CONF ModeReturn to normaloperating mode bypressing the SW-

Model 7815 Parcel Bench Scale User’s Manual13is displayed, press the TEST key andFILT will again be displayed.5. Press the ZERO key. . .BAUD is displa

Model 7815 Parcel Bench Scale User’s Manual14To abort the CALMode at any time,press the SW-1 switch.Step-by-StepInstructions for CALModeCalibration Mo

Model 7815 Parcel Bench Scale User’s Manual155. Press the ZERO key to scroll through theavailable capacity selections. When thechoice you want is disp

Model 7815 Parcel Bench Scale User’s Manual16Step-by-step Instructionsfor RE-CAL ModeFollow these steps to re-configure your scale(without weights). R

Model 7815 Parcel Bench Scale User’s Manual17Review/Test Scale SettingsThe TEST key located on the front panel lets youperform some basic system diagn

Model 7815 Parcel Bench Scale User’s Manual18Communication DE-9 Female Scale DE-9 Male HostPin Name Direction Pin Name Direction1. JMP1 - 1. DCD IN2.

Model 7815 Parcel Bench Scale User’s Manual19Factory default settings: 9600 baud, 7 data bits,even parity, 1 stop bit. Protocol is NCI standardonly.St

Model 7815 Parcel Bench Scale User’s Manual2CAUTIONRisk of electrical shock. Do not remove cover.No user serviceable parts inside. Refer servicing toq

Model 7815 Parcel Bench Scale User’s Manual20TroubleshootingPerform each step in sequence to correct theerror condition. If the problem cannot be cor-

Model 7815 Parcel Bench Scale User’s Manual216. Replace the main board.Display shows center “ _ _ _ ” dashes(Indicates the scale is outside zero capac

Model 7815 Parcel Bench Scale User’s Manual22Spare Parts ListingDESCRIPTION PART NUMBERKeyboard Panel 1163-13204Display PCB 7405-15465Loadcell (75 kg)

Model 7815 Parcel Bench Scale User’s Manual23

1000 Armstrong DriveFairmont, MN 56031Telephone: 507-238-4461Facsimile: 507-238-4195E-Mail: [email protected]

Model 7815 Parcel Bench Scale User’s Manual3Table of ContentsDescription -------------------------------------------------- 4Specifications ----------

Model 7815 Parcel Bench Scale User’s Manual4DescriptionThe NCI Model 7815 is a digital electronic parcelbench scale specifically designed for shipping

Model 7815 Parcel Bench Scale User’s Manual5Over Capacity LimitsScale LevelingDie cast aluminum base with an ABS plasticweight platter. Built-in overl

Model 7815 Parcel Bench Scale User’s Manual6CommunicationsDynamic Response The time from when weight is applied to the scaleto the time when stable we

Model 7815 Parcel Bench Scale User’s Manual7Check container for any obvious evidence ofdamage. Inspect the unit for shipping damage.Immediately report

Model 7815 Parcel Bench Scale User’s Manual8After the NCI Model 7815 is properly installedand power is applied, the display will perform acountdown te

Model 7815 Parcel Bench Scale User’s Manual9Entering Setup ModeYou can access the MENU Mode by pressingswitch 1 shown in Figure 1.In the Menu Mode, th